Statistics
| Branch: | Revision:

adafruit_bno055 / examples / rawdata / rawdata.ino @ 463eabf7

History | View | Annotate | Download (2.841 KB)

1 fcd68623 Kevin Townsend
#include <Wire.h>
2
#include <Adafruit_Sensor.h>
3
#include <Adafruit_BNO055.h>
4
#include <utility/imumaths.h>
5
6
/* This driver reads raw data from the BNO055
7
8
   Connections
9
   ===========
10
   Connect SCL to analog 5
11
   Connect SDA to analog 4
12
   Connect VDD to 3.3V DC
13
   Connect GROUND to common ground
14 f12bf4b5 Tony DiCola
15 fcd68623 Kevin Townsend
   History
16
   =======
17
   2015/MAR/03  - First release (KTOWN)
18
*/
19
20
/* Set the delay between fresh samples */
21 c4f272e1 ladyada
#define BNO055_SAMPLERATE_DELAY_MS (100)
22 f12bf4b5 Tony DiCola
23 fcd68623 Kevin Townsend
Adafruit_BNO055 bno = Adafruit_BNO055();
24
25
/**************************************************************************/
26
/*
27
    Arduino setup function (automatically called at startup)
28
*/
29
/**************************************************************************/
30 f12bf4b5 Tony DiCola
void setup(void)
31 fcd68623 Kevin Townsend
{
32
  Serial.begin(9600);
33
  Serial.println("Orientation Sensor Raw Data Test"); Serial.println("");
34 f12bf4b5 Tony DiCola
35 fcd68623 Kevin Townsend
  /* Initialise the sensor */
36
  if(!bno.begin())
37
  {
38
    /* There was a problem detecting the BNO055 ... check your connections */
39
    Serial.print("Ooops, no BNO055 detected ... Check your wiring or I2C ADDR!");
40
    while(1);
41
  }
42 f12bf4b5 Tony DiCola
43 fcd68623 Kevin Townsend
  delay(1000);
44 f12bf4b5 Tony DiCola
45 0e2e2723 Kevin Townsend
  /* Display the current temperature */
46
  int8_t temp = bno.getTemp();
47
  Serial.print("Current Temperature: ");
48
  Serial.print(temp);
49
  Serial.println(" C");
50
  Serial.println("");
51 f12bf4b5 Tony DiCola
52 c4f272e1 ladyada
  bno.setExtCrystalUse(true);
53 f12bf4b5 Tony DiCola
54
  Serial.println("Calibration status values: 0=uncalibrated, 3=fully calibrated");
55 fcd68623 Kevin Townsend
}
56
57
/**************************************************************************/
58
/*
59
    Arduino loop function, called once 'setup' is complete (your own code
60
    should go here)
61
*/
62
/**************************************************************************/
63 f12bf4b5 Tony DiCola
void loop(void)
64 fcd68623 Kevin Townsend
{
65
  // Possible vector values can be:
66
  // - VECTOR_ACCELEROMETER - m/s^2
67
  // - VECTOR_MAGNETOMETER  - uT
68
  // - VECTOR_GYROSCOPE     - rad/s
69
  // - VECTOR_EULER         - degrees
70
  // - VECTOR_LINEARACCEL   - m/s^2
71
  // - VECTOR_GRAVITY       - m/s^2
72
  imu::Vector<3> euler = bno.getVector(Adafruit_BNO055::VECTOR_EULER);
73 f12bf4b5 Tony DiCola
74 fcd68623 Kevin Townsend
  /* Display the floating point data */
75
  Serial.print("X: ");
76 c4f272e1 ladyada
  Serial.print(euler.x());
77
  Serial.print(" Y: ");
78
  Serial.print(euler.y());
79
  Serial.print(" Z: ");
80
  Serial.print(euler.z());
81 f12bf4b5 Tony DiCola
  Serial.print("\t\t");
82 fcd68623 Kevin Townsend
83
  /*
84
  // Quaternion data
85
  imu::Quaternion quat = bno.getQuat();
86
  Serial.print("qW: ");
87 c4f272e1 ladyada
  Serial.print(quat.w(), 4);
88
  Serial.print(" qX: ");
89
  Serial.print(quat.y(), 4);
90
  Serial.print(" qY: ");
91
  Serial.print(quat.x(), 4);
92
  Serial.print(" qZ: ");
93
  Serial.print(quat.z(), 4);
94 f12bf4b5 Tony DiCola
  Serial.print("\t\t");
95 fcd68623 Kevin Townsend
  */
96 f12bf4b5 Tony DiCola
97
  /* Display calibration status for each sensor. */
98
  uint8_t system, gyro, accel, mag = 0;
99
  bno.getCalibration(&system, &gyro, &accel, &mag);
100
  Serial.print("CALIBRATION: Sys=");
101
  Serial.print(system, DEC);
102
  Serial.print(" Gyro=");
103
  Serial.print(gyro, DEC);
104
  Serial.print(" Accel=");
105
  Serial.print(accel, DEC);
106
  Serial.print(" Mag=");
107
  Serial.println(mag, DEC);
108
109 fcd68623 Kevin Townsend
  delay(BNO055_SAMPLERATE_DELAY_MS);
110 f12bf4b5 Tony DiCola
}